Android app for cut stringers

Stair Calculator

Enter the total rise and pick your boards. Stair Calculator works out the risers and treads, draws the stringer you mark and cut with every measurement on it, and checks the listed residential dimensions for the code you pick.

Some local rules and spiral measurements are reference checks. Verify the applicable edition, site clearances, rails and structural support before cutting.

For Android 8.0 and later. Feet and inches, or millimetres.

  • Free cut diagram
  • Code check with the clause
  • No ads
  • No account
A 57 inch stair worked out as 8 risers of 7 1/8 inches with a 10 inch unit run, drawn from the side, passing the checks listed for IRC 2021.

Cut diagram

See every cut before you make it

  • The stringer on its board. Every notch with its rise and run, the throat, the board length and the stair angle, drawn on the stock board you buy.
  • Where to start marking. The heel line, the first tip and the plumb mark, each measured from the end of the uncut board.
  • The ends drawn large. The bottom and top cuts, with the level cut, the plumb cut and how the stringer meets the rim.
  • Cut or housed. Cut stringers for decks and outdoor stairs, or housed strings for indoor stairs, with each housing, the margin line and the wood left above and below.
  • In your units. Feet, inches and fractions to 1/8, 1/16 or 1/32 inch, decimal inches, or millimetres.

Pinch to zoom, and turn the dimensions off to see the board on its own.

The cut diagram of a 57 inch stair: the stringer on a 96 inch board with every notch, the throat, the board length 84 3/4 inches and the 35.5 degree angle, and where to start marking.

Code check

A code check that shows its work

  • The code that applies to you.
    • IRC 2021
    • 16 US state codes
    • NCC 2022 and 2025
    • Approved Document K
    • Your own limits
  • The value, the limit and the clause. Riser 8 1/8" is over the 7 3/4" maximum (IRC 2021 R311.7.5.1).
  • The range before you type. Each input shows the values that pass, so you pick a passing one first.
  • Fixes that pass. When a check fails, the app offers changes that pass, such as closing open risers or changing the unit run, each checked before you see it.
  • What it leaves to you. "Also required" lists what the code asks for that the app does not check, such as handrails, and says when this stair needs it.
The fix sheet for open risers that leave a 6 1/8 inch gap where IRC 2021 R311.7.5.1 allows under 4 inches, offering riser boards or infill strips, both marked Passes.

One-time unlock

Everything for the whole job

One purchase, not a subscription, adds the job's paperwork and the harder stairs: the marks, landings, winders and spirals, what to buy, saved projects and a cut sheet to print.

See it before you buy: the demo project is a stair with a landing, worked through on every screen, and the unlock screen opens a spiral demo.

Pricing

Free to calculate, one unlock for the job

No ads in either. The unlock is bought once through Google Play, which shows its price in your currency before you buy.

Free

No ads
  • The calculation for a straight flight
  • The code check, with fixes that pass
  • The dimensioned cut diagram, with the bottom and top cuts
  • The summary and code check for winders and spirals
  • Feet and inches, or millimetres
  • Your working stair, remembered for next time
  • The demo project, with every screen
  • The first page of your own cut sheet, to see before you unlock

Unlock

One-time
  • Every mark from either end, and the story pole
  • Up to three landings, with a plan view
  • Winder plans and spiral stairs
  • The materials list
  • Saved projects
  • The PDF cut sheet, to save, share or print
  • Pay once: not a subscription, no expiry

Restore purchase brings it back on a new phone with the same Google account.

Important

Geometry, not certification

Stair Calculator works out geometry. It does not assess structural strength, spans, fixings or footings, it checks only the items it lists, and it does not certify a stair.

It does not replace a licensed builder, engineer or building certifier. If you are unsure about any part of the work, get advice from a qualified person.

Building codes vary by place and edition, and local rules can change the model codes' limits. Confirm the requirements with your local building authority, and check every measurement before you cut.

At a glance

App
Stair Calculator
Platform
Android 8.0 and later
Stairs
Straight flights with cut or housed stringers, up to three landings, winders and spiral stairs
Codes
IRC 2021 and 16 US state codes, NCC 2022 and 2025, Approved Document K, or your own limits
Units
Feet, inches and fractions; decimal inches; millimetres
Price
Free to calculate, with an optional one-time unlock
Ads
None
Account
Not needed
Internet
Not needed to calculate. Used only for Google Play billing
Language
English
Developer
[r]think, Australia
Support
support@rthink.co
Google Play
co.rthink.stairs

Questions

Which building codes does Stair Calculator check?

IRC 2021 (United States) and 16 US state codes that change the model limits; NCC 2022 and 2025, Housing Provisions (Australia); and Approved Document K for private stairs (England). Anywhere else, enter your own limits. Each result gives the value, the limit and the clause.

Does it work in millimetres?

Yes. Choose feet, inches and fractions (to 1/8, 1/16 or 1/32 inch), decimal inches, or millimetres. The cut diagram, the marks and the PDF all follow your choice.

What kinds of stairs can it work out?

Straight flights with cut (notched) stringers or housed strings. With the unlock: up to three landings, each going straight on or turning left or right by 90 or 180 degrees; a quarter or half turn of winders; and spiral stairs round a centre column. Helical stairs are not covered.

What is free?

The calculation for a straight flight, the code check with its fixes, both unit systems, the dimensioned cut diagram with the bottom and top cuts, the summary and code check for winders and spiral stairs, and your working stair, remembered for next time. There are no ads.

What does the unlock add?

Running measurements (every mark along the stringer from either end, and the story pole), up to three landings with each flight's cut diagram and a plan view, the winder plan and set-out, the spiral's plan, headroom section, tread set-out and column marks, the materials list, saved projects and the PDF cut sheet. It is one purchase, not a subscription, and it does not expire.

How much is the unlock?

Google Play shows the price in your currency before you buy. You pay once, and Restore purchase brings it back on a new phone with the same Google account.

Can I see the paid screens before I buy?

Yes. The demo project is a stair with a landing, worked through on every screen, including the ones in the unlock, and the unlock screen opens a spiral demo. Both are read-only. Your own stair's cut sheet shows its first page before you unlock.

Does it check that my stair is strong enough?

No. Stair Calculator works out geometry. It does not assess structural strength, spans, fixings or footings, it checks only the items it lists, and it does not certify a stair. It does not replace a licensed builder, engineer or building certifier: confirm the requirements with your local building authority, and if you are unsure about any part of the work, get advice from a qualified person.

Do I need an account or an internet connection?

No account and no sign-up. Everything is worked out on your phone, and the app uses the internet only for Google Play billing.

What data does Stair Calculator collect?

Your stairs, projects and settings stay on your phone, and a PDF goes only where you save or share it. Nothing is sent to [r]think. Google's billing library, which handles the purchase, sends diagnostic information to Google. The privacy policy has the details.

Is there an iPhone version?

No. Stair Calculator is for Android and needs Android 8.0 or later.

Who makes Stair Calculator?

[r]think, a venture studio in Australia. Support: support@rthink.co.

Get Stair Calculator

Rise and run, the cut diagram and the code check, free. No ads. No account.

Get it on Google Play

Questions? support@rthink.co